This is the base design for my new hand-held controller. Along with a new case and display, I’m going to refactor the software to provide a cleaner interface into the clients (locomotives). Right now my ‘phase A’ handheld knows a little too much about the clients, I want a more disconnected sort of protocol. Anyhow, I’ve gotten everything to fit but the graphic interface required some new hardware so that has not been tested (other than a basic smoke test). I’ll need to write the code for that and then port parts of the old handheld code into it. The keyboard, knob and Xbee interface should not have to change much, I just need a calibration step on the kbd and store that into eeprom. I’m going to have a usb interface into this so I can write a tool on the PC to setup the function keys and display.
In addition to my own control system using Xbees, I also play around with standard radio control. I have one of the Hobby King systems shown above, I think it was like $25 for the TX and RX pair. In the second picture I’ve taken the TX out of the shell and replaced the joy sticks with pots. I’ve mounted it on a board so I can get to it’s innards.
Anyhow, what I’ve done is leverage my R/C signal software and my DCC generation software into one widget. I continuously sample the servo pulse coming out of the R/C RX and then translate that into DCC messages. In this case, throttle messages, although they could be anything.
It all fits into an 8 pin Attiny85, then feeds into my other new widget, the DCC output board.
With this board, one side goes to the battery connection, the other is the output. You can see the small R/C type connector which carries the signal from the Attiny to the board. The DCC output of this board then directly feeds the sound decoder.
Finally, here is a video showing it in action. You can hear the notches of the sound decoder increase as the output pot is twisted and the servo pulse width increases-
Above is the basic install I do on all my locomotives. The green RX box can be a regular R/C RX or it can be my Xbee Control Board. Same basic wiring.
Above is the GE Locomotive ‘Trip Optimizer’ Software. You can see a nice video about it here -> GE Locomotive Trip Optimizer
And here is a really cool video of GE intermodal at work, with the Trip Optimizer of course.
I’ve borrowed some of the graphic layout ideas from this to make the GUI for my phone app- Not quite sure what I want yet but I like this minimalistic implementation.
Again, the idea here is that the phone sits in the cradle (see below) and communicates with the Xbee master in the cradle via bluetooth. The Xbee master reads the knob and the buttons and syncs up with the phone app to keep the display refreshed. The Xbee master controls the Xbee client in the locomotive and also can query the locomotive for speed (via a wheel encoder) and current draw (via a pololu current sensor). There are also hooks available for an RFID reader (I use a somewhat pricey one from Sparkfun – $33) for position information.
Latest incarnation of the Phone Throttle Contraption. The phone communicates with the Xbee Controller via bluetooth, a custom app runs on the phone. This is based on previous experiments with an android tablet, you can read about that here- Android, Bluetooth and Xbee
I’m trying to emulate a generic sort of DCC throttle ‘feel’ with this. I have all of the base code written and tested, it’s just a matter of pulling all the parts together. Slowly I’m getting everything working.
Yet another project in the works. This one is intended to leverage my DCC circuit boards into a interrupt driven DCC I/O system for the Arduino Pro Mini. I actually have all of the software done and tested for both the input and output of DCC signals on my Attiny1634 board but I’ve never actually used a real ‘Arduino’. I’ve always built my own boards so this is a learning experience. I’m probably not going to make it compatible with the larger ‘Arduino’ universe, I’ll just optimize it for the Pro Mini. Anyhow, this project is actually number two on the list, the refurbish of my U25B locomotive is first so I can polish off the main widget code base.
I picked up a cheap Aristocraft U25B in Chessie paint the other day and have been taking it apart so I can rebuild it. The idea is to get from the toy like unit I have into at least a semi-scaled sort of model. The photo above is the closest prototype image I’ve found to what is depicted with this Aristocraft rendition. So I’m stripping it down to the base parts with the idea to install my control system, batteries and sound. And of course, a bit of paint and detail work- it is a bit cheezy with the cast color parts. Yuck. So anyhow, I’m getting there. Below is an image of the original model. More in a later post.
Today I got my order of printed circuit boards from Bay Area Circuits. I promptly populated them with components and powered them all up to see how they would do. Everything works! Very nice! Next step is to install these into one of my locomotives and replace all the breadboards with something clean and production quality.
Pictured, in order, is the 8Amp DPDT relay module, it’s used to reverse the direction of the locomotive. It can be triggered either with a logic one or zero, say from an Ardunio, or from an R/C signal via your generic radio control system. (The logic version is shown, the R/C version has an additional chip on the board, you can see the outline).
Second is the DCC output module. It is designed to be driven with a logic signal from a micro-controller such as the Ardunio. Logic input in, attach your choice of battery (or other) power to the input terminals and it provides up to 3Amps of DCC encoded power on the outputs.
Below that is the DCC input module, connect this to any DCC device like the MRC Prodigy or NCE DCC units and it converts the high voltage DCC signal down to what a micro-controller or Ardunio needs.
The last one is my Control Widget Node. This device is a micro controller wired to an industrial strength Xbee Series 1 802.15.4 Wireless Network Module. I use this for both my Control and Slave nodes. It allows high speed data delivered in an organized network infrastructure with a range of about 300 ft. I send both proprietary packets and DCC messages over this in real time. This is the latest PCB design.
I’ve been doing quite a bit of PCB design these days, here is a version of my controller board, the ‘microwidget’. It’s quite compact. I have not had any made yet but I thought it came out really sort of, well, neat. Like art kinda.
All total I have about five or six small circuits for doing control networks- specifically for large scale model trains. DCC input and output, servo control, DC brushed motor control, reversing relays- all via Industrial strength Xbee Network wireless.
I’m also thinking of making an apt-get debian package to install JMRI on a RPi 2 and gitlab for my code. Hmm.
I think I need a Kickstarter 🙂
Here are the final two prototypes. The master obviously connects to the Prodigy Express and sports a long range antenna for max transmission power. What I’m thinking here is this is the module that will be connected to my RPi 2 which I am planning on running JMRI on. The Pi 2 will also have a long range wifi antenna on it so I can use it to source web pages to my phone and tablet. My standard handheld design is what I actually use to drive my trains with.
The second pic is the client. This one is fairly comprehensive and has quite a few parts but I use it as my standard prototype rig. In addition to the control board, it also has an (expensive) Pololu 18v7 motor controller and a current sensor. The DCC output stage is the board with the large chip beside the speaker. All it is used for in this incarnation is to drive the Econami Diesel DCC decoder which powers the speaker on the right.
Here are all the parts labeled, you can click on the picture for a larger version-